B-VER Construction Sdn Bhd, (549929-w) 10-01, Lorong Batu Nilam 20B, Bandar Bukit Tinggi 2, 41200 Klang, Selangor D.E, Tel.603-3324 1403 603-3325 5835 Fax:603-3323 3548 www.bverconstruction.com .
The company is fully committed to safety as it has been awarded several safety awards from previous projects.
08:00
bverconstruction
07:58
bverconstruction
07:48
bverconstruction
05:34
bverconstruction
Description
A modified acrylic resim system dispersed in a mixture of solvents. Its use to seal and protect concrete
substrate from ingressing of dirt and provides an easier cleaning surface.
Area to Use
The product can be applied to most concrete surface.
Existing Concrete
Ensure that the substrate is clean and dry. Remove any efflorescence by an acid etch, high acid.
Typical Properties
Melting Point / Boiling Point N/A
Vapor Pressure N/A
Specific Gravity 0.92
Flash Point 27°C
Solubility in water Insoluble
Solid (PBW) 25%
Appearance Clear Liquid or With Colour
Application
Use as a concrete sealer,
# Pour on with cone or tube
Packing:-
SEALER BV 64 is packed in 5 litres or 18 litres pail.
Storage
Xyleen: Storage cool and dry, away from heat sources, flammable areas.
Description and uses
Sealer BV 64 is an acrylic base concrete sealer designed for finishing new interior or exterior
concrete. It is also a durable sealer and finish coat for refurbishing older coloured, chemically
stained, or uncoloured concrete flatwork. It gives the surface an attractive appearance and
enhance depth of colour while offering an easy-to-maintain, semi-gloss finish and added resistance to staining.
As a sealer and finish coating, Sealer BV 64 is helped in preventing concrete dusting and reduces
surfaces staining from materials such as automotive grease, oil and food spills. It produces a
low-maintenance, easy-to-clean film, resistant to abrasion, weather and ultraviolet (UV) radiation.
Warehouse, factory and many other interior coloured or uncoloured concrete floors should
normally be sealed to protect the concrete surface and facilities clean up.
Recommended for :-
- Concrete floor
- Textured concrete floor
- Coloured concrete floor
- Brick walls
- Slates
- Sandstone
Coverage
Sealer BV 64 must be applied full strength without thinning by roller, airless sprayer or by brush. The
coverage will very depending on the method of application and the porosity and texture of the concrete.
Two thin coats are recommended for new uncoated concrete. One coat is usually sufficient on
concrete preciously coated with Sealer BV 64. As a general rule of tumb, an 18 litre tin covers
approximately 60m2 – 70m2.
Preparation
Before application, the concrete surface must be clean of all dirt, oil and grease. Coatings and curing
membranes, other than previously applied Sealer BV 64, must be stripped. Failure to remove all
contaminants and coatings will cause appearance defects, adhesion loss, peel, and reduced durability.
All washed or wet areas should be allowed to dry thoroughly before application of Sealer BV 64.
Application
The coating must be applied thinly and uniformly. Immediately prior to use, the liquid materials should
be thoroughly mixed. Application of two coats id recommended. The second coat should be applied after
the first coat is completely dry, a minimum of 4 hours. Sealer BV 64 must be allowed to dry completely,
normally a minimum of 12 hours after application of the second coat. Finished surface should be protected
from damage by other trades.
Availability
Sealer BV 64 is obtainable from:-
B-VER CONSTRUCTION SDN BHD
Add : 12A-01-01, Lorong Batu Nilam 1B,
Bandar Bukit Tinggi, 41200 Klang,
Selangor Darul Ehsan.
Tel: 03-3324 1403
Fax: 03-3323 3548
E-mail: bverconst@yahoo.com
Coverage: 60m2 – 70m2 / 18 litre
Maintenance and removal
Sealer BV 64 surfaces should be maintained by sweeping. Spills should be cleaned up when they
occur. Dirt may be hosed off with water. On area subject to heavy use or more severe conditions,
periodic general cleaning should be performed using a high-quality commercial detergent and automatic
scrubber equipment.
A maintenance application of Sealer BV 64 should be made periodically as the coating is worn off
the surface. The need for maintenance coating will be accelerated in area of heavy use.
It is not necessary to strip the previously applied coating unless film build up is heavy of the surface
cannot be cleaned sufficiency. Solvent can be applied to remove existing Sealer BV 64.
Limitation
Sealer BV 64 must only be used in thin coats on surface adequately textured for slip resistance unless
used on surface previously coated with the sealer, they must be porous to allow penetration. If applied
improperly or too heavily, the surface may whiten, peel, or become slippers, particulars on pool decks
or other area where water may collect and stand on the surface.
Sealer BV 64 is a premium-quality sealer and finish coating, but like allcoatings, will require periodic
maintenance and reapplication. Spills should be removed promptly and floors cleaned regularly to
minimize possible staining and damage to the finish coat.
05:33
bverconstruction
Description
B-VER RELEASER AGENT is a ready to use, dry shake releaser available in variety of colours. It is used to
release moulds for decorative imprinting from sticking to the concrete surface. B-VER Releaser Agent also
acts as curing compound and colouring agent to give a desired two tone effect.
Physical Description / Properties
Appearance Odorless coloured po
Boiling point / melting point Approximate 150 Degrees Celsius
Vapor Pressure N/A
Specific Gravity N/A
Flash Point > 250 Degrees Celsius
Flammability N/A
Solubility in Water Insoluble
Packing
B-VER RELEASER AGENT is packed in 14kg/bag. Stir well before use.
Shelf Life
Under normal conditions and kept dry, the shelf life of the releaser is 3 years from the date of manufacture.
Rate of Application
0.1 – 0.13kg/m2
Application
As soon as the application of B-VER Colour Hardener is complete and ready to print, linal trowel the surface of
the colour hardener and dry shake the B-VER Releaser Agent and applied the required tools to form the pattern surface.
Wash and Seal
One or two days after imprint, wash excess releaser off job with water or sweep dry. After 5-7 daysthe surface
should be cleaned with a high pressure cleaner. Rough surfaces shall be grind-down and touch-up if any. After
washing and the surface is completely dry, apply 2 coats Sealer BV 64. Allow the first coat to dry before
application of second coat.
Protection
The finished floor shall be protected. Any heavy traffic shall be avoided for 28 days.(The main contractor
shall take necessary steps to protect the finished floor from damage by other trades)
05:28
bverconstruction
Description
B-VER BV29 Colour Hardener is a ready to use dry silica quartz mineral aggregate, suitable for finishing, hardening and coluring over fleshly floated and leveled concrete flatwork where the surface is required to be stamped or stenciled.
Use
B-VER BV29 Colour Hardener is suitable for both interior and exterior and where areas require additional wear resistance
such as:-
Ø Car park/entrance of Bungalows
Ø Main entrance of Hotels and Condominium
Ø Swimming Pool Deck
Ø Pavement Walks
Materials Composition
B-VER BV29 Colour Hardener consist of hard wearing silica quartz mineral of property sizes and graded aggregate, dispersing agents,strength promoter and cement binder. Whenavailable in colours, the pigments which are integrand uniformly and have good UV resistance.
Packing
B-VER BV29 Colour Hardener is packed in 40 Kg/bag.
Shelf Life
Under normal conditions and kept dry the shelf life of the surface hardener is at least 6 months from the date of manufacture.
Colours
B-VER BV 29 Colour Hardener is ready available in a wide range of colours, where customized colour is requires the colour
hardener can also be formulated to specification with sufficient prior notification and quantities.
Properties
v Compressive strength at 28days: 65n/mm.
v Abrasion resistance is 200% great than plain concrete
v Hardener of aggregate is Moh’s scale 7
Rate of Use
3 to 4kg/m2
Application
After the concrete has been screed, consolidate and further level by bull float and any free water has evaporated or
been removed, the surface should be floated by hand or bull floated. Immediately following this floating operation, shake
the B-VER Colour Hardener by and over the surface. The first application of the B-VER olour Hardener should use
about 2/3 of the total amount needed. The dry shake material will absorb some moisture from the freshly prepared
concrete and should than be thoroughly floated into the surface, preferably by a bull loat immediately after this the
remainder of the specified amount of the B-VER Colour Hardener should be distributed evenly over the surface at right
angles to the previous application. This should be thoroughly floated and take part of the surface taking care that a
uniform colours is obtained. Final toweling is best done by hand.
Protection
The finished floor shall be protected and heavy traffic shall be avoided for approximately 28 days.
The Contractor or principal shall take necessary steps to protect the finishes floor from damage by other trades.
The representation and recommendation regarding the product are based on test, which we believe are reliable.
We cannot accept responsibility or guarantee of success of your work as we have no influence or control over
the method of application, site condition etc.
